Mechanical Engineering for Society and Industry

Articles

Experimental study on a new prototype design of electric bus vehicle structure under torsion loading conditions

Budi Haryanto , Danardono Agus Sumarsono , Djoko Wahyu Karmiadji , Mohammad Adhitya , Stevanus Brian Kristianto , Lukyawan Pama Deprian

Published
December 28, 2025

Vol. 5 No. 2 (2025)
Pages 425-433

DOI

Open Access
Share

Abstract

Vehicles commonly encounter uneven road conditions, which can lead to torsional deformation of the frame structure. The results of finite element analysis (FEA) indicate that the highest stress occurs under torsion loading conditions. To validate these simulation results, an experimental study was conducted involving static load testing under torsional loading conditions on a hybrid frame structure, composed of SS 400 carbon steel and 6061 aluminum alloy, designed for a 70-passenger electric bus. The test was performed by applying a static load of 6,825 kg as sandbags on the seating area and aisle, and supporting the frame on three wheels only. Strain measurements were recorded using 28 strain gauges: 20 on the SS 400 carbon steel underframe and 8 on the 6061 aluminum alloy structure of the side and roof frames. The total load was the weight of 70 passengers plus a 30% dynamic load factor. Experimental analysis revealed a maximum stress value of 76.42 MPa in the SS 400 carbon steel of the underframe at location 9 in the central section of the underframe. In the 6061 aluminum alloy structure, the maximum stress value of 15.56 MPa was obtained in the roof frame directly below the air conditioner unit. Overall, the measured stress values were within the elastic ranges of the materials used, demonstrating structural integrity under load. The average difference between the experimental results for stress and the finite element analysis (FEA) simulation was approximately 11.21%.

Keywords

Electric bus; Torsion; Strain gauge; Stress

References

  1. [1] S. Karlilar Pata, S. Erdogan, U. K. Pata, and M. S. Meo, “Greening road transport: Comparison of technologies in conventional, hybrid, and electric vehicles,” Journal of Environmental Management, vol. 380, no. December 2024, p. 124908, Apr. 2025, doi: 10.1016/j.jenvman.2025.124908.
  2. [2] H. A. El Daheb, R. A. Sayed, M. Salah, and M. A. Mosbah, “Impact-Based Energy Consumption Mitigation by Changing the Light Electric Vehicle Weight on the Drive Cycle,” Automotive Experiences, vol. 8, no. 3, 2025, doi: 10.31603/ae.14668.
  3. [3] M. Mahmoud, R. Garnett, M. Ferguson, and P. Kanaroglou, “Electric buses: A review of alternative powertrains,” Renewable and Sustainable Energy Reviews, vol. 62, pp. 673–684, Sep. 2016, doi: 10.1016/j.rser.2016.05.019.
  4. [4] D. Göhlich, T.-A. Fay, D. Jefferies, E. Lauth, A. Kunith, and X. Zhang, “Design of urban electric bus systems,” Design Science, vol. 4, p. e15, Aug. 2018, doi: 10.1017/dsj.2018.10.
  5. [5] M. Hamurcu and T. Eren, “Electric Bus Selection with Multicriteria Decision Analysis for Green Transportation,” Sustainability, vol. 12, no. 7, p. 2777, Apr. 2020, doi: 10.3390/su12072777.
  6. [6] K. W. Lie, T. A. Synnevåg, J. J. Lamb, and K. M. Lien, “The Carbon Footprint of Electrified City Buses: A Case Study in Trondheim, Norway,” Energies, vol. 14, no. 3, p. 770, Feb. 2021, doi: 10.3390/en14030770.
  7. [7] S. B. Kristianto et al., “Experimental Stress Analysis on Frame Structure of A 70-Passengers Electric Bus,” Automotive Experiences, vol. 8, no. 2, pp. 401–414, Sep. 2025, doi: 10.31603/ae.13757.
  8. [8] D. Berjoza and I. Jurgena, “Effects of change in the weight of electric vehicles on their performance characteristics,” Agronomy Research, vol. 15, no. 1, pp. 952–963, 2017.
  9. [9] A. P. Gusti et al., “A Systematic Literature Review of Risk Assessment Methodologies for Battery Electric Vehicles,” Automotive Experiences, vol. 8, no. 1, pp. 46–71, Mar. 2025, doi: 10.31603/ae.12835.
  10. [10] V. H. Quan, K. K. Evgenievich, N. T. Duc, and K. F. Kirillovich, “Development and Evaluation of Passive Balancing System Model for Lithium-Ion Battery Pack in Electric Vehicles Using Numerical Simulation,” Automotive Experiences, vol. 8, no. 2, pp. 390–400, Sep. 2025, doi: 10.31603/ae.13320.
  11. [11] F. E. Saldanha, S. D. A. Sousa, G. L. De Gouveia, M. Dwek, and J. E. Spinelli, “Evaluation of 6000 Al Alloys for Application in Chassis of Electric Vehicles,” Materials Research, vol. 25, 2022, doi: 10.1590/1980-5373-mr-2022-0275.
  12. [12] M. Choi, J. Cha, and J. Song, “Impact of lightweighting and driving conditions on electric vehicle energy consumption: In-depth analysis using real-world testing and simulation,” Energy, vol. 323, p. 135746, May 2025, doi: 10.1016/j.energy.2025.135746.
  13. [13] O. Ahmadzadeh, R. Rodriguez, J. Getz, S. Panneerselvam, and D. Soudbakhsh, “The impact of lightweighting and battery technologies on the sustainability of electric vehicles: A comprehensive life cycle assessment,” Environmental Impact Assessment Review, vol. 110, no. August 2024, p. 107668, Jan. 2025, doi: 10.1016/j.eiar.2024.107668.
  14. [14] J. Zhang, Y. Deng, B. Zheng, and X. Qi, “Lightweight design of low-load electric vehicle frame,” Journal of Computational Methods in Sciences and Engineering, vol. 21, no. 2, pp. 423–433, May 2021, doi: 10.3233/JCM-204530.
  15. [15] C. L. Fu, Y. C. Bai, C. Lin, and W. W. Wang, “Design optimization of a newly developed aluminum-steel multi-material electric bus body structure,” Structural and Multidisciplinary Optimization, vol. 60, no. 5, pp. 2177–2187, Nov. 2019, doi: 10.1007/s00158-019-02292-w.
  16. [16] S. Nandhakumar, S. Seenivasan, A. Mohammed Saalih, and M. Saifudheen, “Weight optimization and structural analysis of an electric bus chassis frame,” Materials Today: Proceedings, vol. 37, no. x, pp. 1824–1827, 2021, doi: 10.1016/j.matpr.2020.07.404.
  17. [17] R. Yang, W. Zhang, S. Li, M. Xu, W. Huang, and Z. Qin, “Finite Element Analysis and Optimization of Hydrogen Fuel Cell City Bus Body Frame Structure,” Applied Sciences, vol. 13, no. 19, p. 10964, Oct. 2023, doi: 10.3390/app131910964.
  18. [18] C. Yao and M. Yang, “Analysis of Strength Stiffness and Modes for Bus Body Frame,” Journal of Physics: Conference Series, vol. 1748, no. 6, p. 062073, Jan. 2021, doi: 10.1088/1742-6596/1748/6/062073.
  19. [19] H. S. Hanandita, U. Ubaidillah, A. R. Prabowo, B. W. Lenggana, A. Turnip, and E. Joelianto, “Static Structural Analysis of Checking Fixture Frame of Car Interior Using Finite Element Method,” Automotive Experiences, vol. 6, no. 3, pp. 652–668, Dec. 2023, doi: 10.31603/ae.9860.
  20. [20] B. Haryanto, M. Nuramin, D. W. Karmiadji, and M. Perkasa, “Verification of a new prototype design of bogie monorail frame with variation of static loading,” Mechanical Engineering for Society and Industry, vol. 3, no. 2, pp. 78–85, 2023, doi: 10.31603/mesi.9905.
Article Metrics
10
Views
57
Downloads

SCITE

DIMENSIONS

Publication Information
Published December 28, 2025
Section Articles
Copyright Copyright (c) 2025 Budi Haryanto, Danardono Agus Sumarsono, Djoko Wahyu Karmiadji, Mohammad Adhitya, Stevanus Brian Kristianto, Lukyawan Pama Deprian
Keywords
  • Electric bus
  • Torsion
  • Strain gauge
  • Stress