Article Sidebar

Download
PDF
Statistic
Read Counter : 952 Download : 582

Downloads

Download data is not yet available.

Main Article Content

Abstract

Natural fiber materials are the sustainable sources used for future automotive elements, where the centrifugal clutch utilizes the frictional force on the clutch pads to transfer kinetic energy from the rotating crankshaft to the transmission and the wheels. These pads are produced from several natural composites, such as coconut fiber, as well as wood and shellfish powder, whose characteristics are being investigated for hardness, microstructure, and wear properties. Based on this study, performance analysis was carried out on the samples of composite centrifugal clutch applied to automatic motorcycles. As a comparison, subsequent analysis was conducted on the genuine clutch pad materials, where the results showed differences in the characteristics of each mixture composition of the natural fiber composites. This indicated that the addition of wood powder composition to the clutch pad increased the hardness and special wear values by an average of approximately 12.9 and 1.16%, respectively. Furthermore, the composite content was observed in the microstructure, as the maximum power and torque on the natural fiber materials were 10.7 hp and 17.17 N.m, respectively. The value was found to be closely similar to the genuine parts with maximum power and torque of 10.8 hp and 16.02 N.m, respectively.

Keywords

Natural fiber Wood powder Coconut fiber Shellfish shell Clutch pad

Article Details

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

References

  1. A. B. D. Nandiyanto, D. F. Alhusaini, R. Ragadhita, and T. Kurniawan, "Resin-based Brake Pad from Rice Husk Particles: From Literature Review of Brake Pad from Agricultural Waste to the Techno-Economic Analysis," Automotive Experiences, vol. 4, no. 3, pp. 131-149, 2021.
  2. N. Chand and M. Fahim, "1 - Natural fibers and their composites," in Tribology of Natural Fiber Polymer Composites: Woodhead Publishing, 2008, pp. 1-58.
  3. A. B. D. Nandiyanto, S. N. Hofifah, G. C. F. Girsang, S. F. Putri, B. A. Budiman, and F. Triawan, "The Effects of Rice Husk Particles Size as A Reinforcement Component on Resin-Based Brake Pad Performance: From Literature Review on the Use of Agricultural Waste as A Reinforcement Material, Chemical Polymerization Reaction of Epoxy Resin, to Experiments," Automotive Experiences, vol. 4, no. 2, pp. 68-82, 2021.
  4. F. Triawan, A. Nandiyanto, I. Suryani, and B. Budiman, "The Influence of Turmeric Microparticles Amount on The Mechanical and Biodegradation Properties of Cornstarch-Based Bioplastic Material: from Bioplastic Literature Review to Experiments," Materials Physics and Mechanics, vol. 46, pp. 99-114, 01/06 2021, doi: 10.18720/MPM.4612020_10.
  5. Sutikno, B. Pramujati, S. D. Safitri, and A. Razitania, "Characteristics of Natural Fiber Reinforced Composite for Brake Pads Material," AIP Conference Proceedings, vol. 1983, no. 1, p. 050009, 2018, doi: 10.1063/1.5046282.
  6. H. Jaya, N. Z. Noriman, H. K. AbdulKadir, O. S. Dahham, N. Muhammad, and N. A. A. Latip, A. K., "The Effects of Wood Sawdust Loading on Tensile and Physical Properties of Up/Pf/Wsd Composites," IOP Conference Series: Materials Science and Engineering, vol. 454, p. 012193, 2018/12/12 2018, doi: 10.1088/1757-899x/454/1/012193.
  7. B. Vijaya Ramnath, J. Jeykrishnan, G. Ramakrishnan, B. Barath, E. Ejoelavendhan, and P. Arun raghav, "Sea Shells And Natural Fibers Composites: A Review," Materials Today: Proceedings, vol. 5, no. 1, Part 1, pp. 1846-1851, 2018/01/01/ 2018, doi: https://doi.org/10.1016/j.matpr.2017.11.284.
  8. T. H. Silva, J. Mesquita-Guimarães, B. Henriques, F. S. Silva, and M. C. Fredel, "The Potential Use of Oyster Shell Waste in New Value-Added By-Product," Resources, vol. 8, no. 1, p. 13, 2019. [Online]. Available: https://www.mdpi.com/2079-9276/8/1/13.
  9. J. Bijwe, "Composites as Friction Materials: Recent developments in Non-Asbestos Fiber Reinforced Friction Materials: A Review," Polymer Composites, vol. 18, no. 3, pp. 378-396, 1997, doi: https://doi.org/10.1002/pc.10289.
  10. P. V. Gurunath and J. Bijwe, "Friction and Wear Studies on Brake-Pad Materials Based On Newly Developed Resin," Wear, vol. 263, no. 7, pp. 1212-1219, 2007/09/10/ 2007, doi: https://doi.org/10.1016/j.wear.2006.12.050.
  11. A. L. Crăciun, C. Pinca-Bretotean, C. Birtok-Băneasă, and A. Josan, "Composites Materials for Friction and Braking Application," IOP Conference Series: Materials Science and Engineering, vol. 200, p. 012009, 2017/05 2017, doi: 10.1088/1757-899x/200/1/012009.
  12. R. C. Pettersen, "The Chemical Composition of Wood," in The Chemistry of Solid Wood, vol. 207, (Advances in Chemistry, no. 207): American Chemical Society, 1984, ch. 2, pp. 57-126.
  13. S. Kocaman, G. Ahmetli, A. Cerit, A. Yucel, and M. Gozukucuk, "Characterization of Biocomposites Based on Mussel Shell Wastes," World Academy of Science, Engineering and Technology, International Journal of Materials and Metallurgical Engineering, vol. 10, pp. 438-444, 2016.
  14. J. Abutu, S. A. Lawal, M. B. Ndaliman, R. A. Lafia-Araga, O. Adedipe, and I. A. Choudhury, "Effects of Process Parameters on The Properties of Brake Pad Developed from Seashell as Reinforcement Material Using Grey Relational Analysis," Engineering Science and Technology, an International Journal, vol. 21, no. 4, pp. 787-797, 2018/08/01/ 2018, doi: https://doi.org/10.1016/j.jestch.2018.05.014.
  15. A. Kholil, S. T. Dwiyati, R. Riyadi, J. P. Siregar, N. G. Yoga, and A. I. Aji, "Characteristics of Wood Powder, Coconut Fiber and Green Mussel Shell Composite for Motorcycle Centrifugal Clutch Pads," IOP Conference Series: Materials Science and Engineering, vol. 1098, no. 6, p. 062034, 2021/03/01 2021, doi: 10.1088/1757-899x/1098/6/062034.
  16. M. F. Kussuma H S and Sutikno, "Testing of Mechanical Characteristics of Coconut Fiber Reinforced for Composite Brake Pads for Two-Wheeled Vehicles," IOP Conference Series: Materials Science and Engineering, vol. 546, no. 4, p. 042018, 2019/06/01 2019, doi: 10.1088/1757-899x/546/4/042018.
  17. A. Kholil, S. T. Dwiyati, Riyadi, and H. P. Randika, "Performance Testing of Motorcycle Centrifugal Clutch Lining Made from Composite Wood Powder, Coconut Fiber, and Green Mussel Shell," Journal of Physics: Conference Series, vol. 2019, no. 1, p. 012065, 2021/10/01 2021, doi: 10.1088/1742-6596/2019/1/012065.
  18. R. S. Khurmi and J. K. Gupta, A Textbook of Machine Design. Eurasia Publishing House Limited, 2004.
  19. W. C. Orthwein, Clutches and Brakes: Design and Selection. Taylor & Francis, 2004.
  20. M. Milosevic, P. Valášek, and A. Ruggiero, "Tribology of Natural Fibers Composite Materials: An Overview," Lubricants, vol. 8, no. 4, p. 42, 2020. [Online]. Available: https://www.mdpi.com/2075-4442/8/4/42.
  21. S. S. Hartati, E; Fatriasari, W; Hermiati, E; Dwianto, W; Kaida, R; Baba, T; Hayashi, "Wood Characteristic of Superior Sengon Collection and Prospect of Wood Properties Improvement through Genetic Engineering," Wood Research Journal, vol. 1, 10/01 2010.
  22. S. Bello, J. Agunsoye, B. Hassan, M. Zebaze Kana, and I. Raheem, "Epoxy Resin Based Composites, Mechanical and Tribological Properties: A Review," Tribology in Industry, vol. 37, 12/01 2015.
  23. D. Chan and G. Stachowiak, "Review of Automotive Brake Friction Materials," Proceedings of The Institution of Mechanical Engineers Part D-journal of Automobile Engineering - PROC INST MECH ENG D-J AUTO, vol. 218, pp. 953-966, 09/01 2004, doi: 10.1243/0954407041856773.
  24. G. Sundarapandian and K. Arunachalam, "Investigating Suitability of Natural Fiber-Based Composite as An Alternative to Asbestos Clutch Facing Material in Dry Friction Clutch of Automobiles," IOP Conference Series: Materials Science and Engineering, vol. 912, p. 052017, 2020/09/12 2020, doi: 10.1088/1757-899x/912/5/052017.
  25. G. Akıncıoğlu, S. Akıncıoğlu, H. ÖKtem, and İ. Uygur, "Brake Pad Performance Characteristic Assessment Methods," International Journal of Automotive Science And Technology, pp. 67-78, 03/31 2021, doi: 10.30939/ijastech..848266.
  26. N. Elzayady and R. Elsoeudy, "Microstructure and wear mechanisms investigation on the brake pad," Journal of Materials Research and Technology, vol. 11, pp. 2314-2335, 2021/03/01/ 2021, doi: https://doi.org/10.1016/j.jmrt.2021.02.045.
  27. K. Hamada and P. D. M. M. Rahman, "An Experimental Study for Performance and Emissions of A Small Four-Stroke SI Engine for Modern Motorcycle," International Journal of Automotive and Mechanical Engineering, vol. 10, pp. 1852-1865, 12/30 2014, doi: 10.15282/ijame.10.2014.3.0154.
  28. I. W. Sugita, D. R. B. Syaka, and A. I. Wahyudi, "Effect of Pertalite – Methanol Blends on Performance and Exhaust Emission of a Four-stroke 125 CC Motorcycle Engine," KnE Social Sciences, vol. 3, no. 12, 03/25 2019, doi: 10.18502/kss.v3i12.4105.
  29. A. B. D. Nandiyanto, F. Triawan, R. Firly, and K. Kishimoto, "Crystallite Size on Micromechanical Characteristics of WO3 Microparticles," Journal of Engg. Research, vol. 9, no. 3A, pp. 268-277, 2021.
  30. T. I. Mohammed, O. O. Ojo, and O. E. Olufemi, "Laboratory Study of a Lignocellulosic Biomass as an Alternative Base Material for Brake Pads," Current Journal of Applied Science and Technology, vol. 29, no. 1, pp. 1-14, 2018.
  31. O. R. Adetunji, A. M. Adedayo, S. O. Ismailia, O. U. Dairo, I. K. Okediran, and O. M. Adesusi, “Effect of silica on the mechanical properties of palm kernel shell based automotive brake pad,” Mechanical Engineering for Society and Industry, vol. 2, no. 1, pp. 7–16, 2022.

Most read articles by the same author(s)